Features :
- Safety Interlock
- Test verification
- 10 sets of memory
- Large Graphic LCD
- Compact, 2U half rack
- Front Panel Calibration
- TÜV-GS mark ( NO. S 50010561)
- Link with new 7100 series Hipot testers
Product Features :
- Large Graphic 128 x 64 LCD indicator that can completely display all testing results
- Large Graphic 128 x 64 LCD indicator that can completely display all testing results
- High-accuracy voltage/current testing analysis (16-bit) that improves the accuracy of measurement
- Programmable 100 memory that can be easily recall the test setup to improve the efficiency of automatic testing
- Dynamic Load measurement, with the effective dynamic band width and speed being able to reach 10KHz
- Minimum input resistance allows the input voltage to be as low as 1V while operating with operating with full current, which satisfies the requirement of minimal voltage testing.
- It can measure constant voltage (CV), constant current (CC), constant resistance (CR), dynamic load (DCC) mode and short circuit output analog.
- It can set upper and lower limits for PASS and FAIL judgement during testing whereby it will automatically determines if the set range has been exceeded or not
- It can set the maximum and minimum short circuit current and also the short circuit time
- The frame can accommodate single-module single channel or dual channel and it can configure up to 8 saparate channels with the maximum capacity being 1200W
- Build-in PLC Remote, GPIB and RS232 interface in the four module frame for automatic testing application (ATS)
- It can directly control the generated waveform of the electronic load by the external input of 0-10V analogue signals
- It can be connected to the oscilloscope to monitor the current waveform via the I monitor BNC connector
- Remote voltage sense for V sense is used for precision voltage measurement that can eliminate the measuring errors caused by voltage drop
- It has various protection features, to include over-voltage protection (OVP), over-current protection (OCP), over-power protection (OPP), over-temperature protection (OTP) and reserve voltage protection (REV).
Brand new Extech 6800 Series Digital AC Power Source is designed in such as way to test on low power products in overall focused features of low height in size and high precise measurement. The height of a 6800 Series AC Power Source of 1KVA capacity will have only 8.9 CM and becomes the smallest AC source in the market.
As the awareness to protect our environment has been increased, it is common consensus to make full used of our energy resources effectively. Country such as Europe and U.S.A defined that all electrical appliance products must be low power consumption when the product is idle or in standby mode. Therefore, it is important for AC Power Source that has the capability of measuring low power of low current.
For 6800 series, it is capable to offer as an option to measure current in resolution of 0.1mA/0.01W. It saves cost for purchasing additional Power Meter as well as reduces issues of space of total equipment occupied. In short, Extech 6800 series provides complete solution in supplying power to your products.
Brand new 6700 series Programmable AC Power Source is designed to supplay and test electronics products of high inrush startup. High crest factor of output (CF≥4) and its echanced startup function of loads maintain output operation at longer period (1000mS) without false cut off, and it is achieved by new linear amplifying circuit design, resulting in clean sine wave, low noise and high stability output.
6700 series is a programmable and user-friendly interface design. Moreover, it can also simulate the characteristic of various loads such as switching type of power loads ( For example : ATX Power, Adapter and Battery Charger ) for the application of inrush current test, Ramp Up tests for input voltage, periodic cut off test, ON/OFF power test and etc. For 6700 Series, it is capable to offer as an option to measure current in resolution of 0.1mA/0.01W that it is suitable to test low power products such as chargers/adapters of cell phones, PDA, digital camera and etc. For model 6710 (1KVA capacity), the height is only 8.9cm. Hence, the brand new 6700 series becomes the best choice of automatic supply and test for electronics products by EEC as it effectively saves extra cost of Power Meter and reduces issue on insufficient space consumed by numerous equipments.
6700 series is a programmable and user-friendly interface design. Moreover, it can also simulate the characteristic of various loads such as switching type of power loads ( For example : ATX Power, Adapter and Battery Charger ) for the application of inrush current test, Ramp Up tests for input voltage, periodic cut off test, ON/OFF power test and etc. For 6700 Series, it is capable to offer as an option to measure current in resolution of 0.1mA/0.01W that it is suitable to test low power products such as chargers/adapters of cell phones, PDA, digital camera and etc. For model 6710 (1KVA capacity), the height is only 8.9cm. Hence, the brand new 6700 series becomes the best choice of automatic supply and test for electronics products by EEC as it effectively saves extra cost of Power Meter and reduces issue on insufficient space consumed by numerous equipments.
